Peripheral Simulation

For Infineon C509-L — Serial UART 0

Simulation support for this peripheral or feature is comprised of:

• Dialog boxes which display and allow you to change peripheral configuration.
• VTREGs (Virtual Target Registers) which support I/O with the peripheral.

These simulation capabilities are described below.

Serial Channel-0 Dialog

The Serial Channel 0 dialog displays and allows you to edit the configuration of the Serial Interface.

• Mode displays and allows you to change the serial interface mode of operation (data length, synchronous or asynchronous).
• S0CON (Serial Control Register 0) holds the control and setup information for programming serial port 0.
• S0BUF (Serial Interface Buffer Register 0) contains the transmit data to be sent or received data.
• SM20 (Enable Serial Port 0 Multiprocessor Communication In Modes 2 and 3) is set to suppress a receiver interrupt (RI0) if the received 9th data bit is 0.
• TB80 (Serial Port 0 Transmitter Bit 9) is the 9th data bit to be transmitted for serial modes 2 and 3.
• REN0 (Receiver Enable) is set to enable serial data input.
• RB80 (Serial Port 0 Receiver Bit 9) is set for serial modes 2 and 3 when a 9th bit is received. In serial mode 1, this is the stop bit.

IRQ

• TI0 (Transmitter Interrupt Flag) is set by hardware for each character frame transmitted. TI0 is cleared by software.
• RI0 (Receiver Interrupt Flag) is set by hardware for each character frame received. RI0 is cleared by software.

BaudRate

• S0RELH (Baudrate Generator Reload High Value) contains the upper 2-bits of the 10-bit value that automatically reloads into the 10-bit timer that generates the baudrate.
• S0RELL (Baudrate Generator Reload Low Value) contains the lower byte of the 10-bit value that automatically reloads into the 10-bit timer that generates the baudrate.
• SMOD (Double Baudrate) is set to double the baudrate in all modes.
• BD (Baudrate Generator Enable) is set to enable the dedicated baudrate generator. If reset, the Timer 1 overflow rate determines the baudrate.
• Baudrate is the actual baudrate for the serial channel. It can be derived from the oscillator frequency, or generated by Timer 1.

SxIN VTREG
Data Type: unsigned int

The SxIN VTREG represents the serial input of the simulated microcontroller. Values you assign to SxIN are input to the serial channel 0, 1, 2, and so on. You may assign input using the command window. For example,

S0IN='A'

causes the simulated microcontroller serial input 0 to receive the ASCII character A. If you want to use the SxIN VRTEG to simulate reception of multiple characters, you must be sure to delay for at least one character time between successive assignments to SxIN. This may be done using a signal function. For example:

signal void send_cat (void) {
swatch(0.01);  /* Wait 1/100 seconds */
S0IN='C';      /* Send a C */
swatch(0.01);
S0IN='A';
swatch(0.01);
S0IN='T';
}

You may use the SxIN VTREG to input more than 8 bits of data. For example,

S0IN=0x0123

inputs a 9-bit value. This is useful if you use 9-bit serial I/O. In addition to the SxIN VRTEG, the serial window allows you to input serial characters by simply typing. Serial characters that are transmitted byt the simulated microcontroller appear in the serial window.

SxOUT VTREG
Data Type: unsigned int

The SxOUT VTREG represents the serial output from the simulated serial port 0, 1, and so on. Whenever the simulated serial port transmits a character, the value transmitted is automatically assigned to SxOUT (which is read-only). You may read the value of SxOUT to determine the character transmitted by your simulated program. For example,

S0OUT

outputs the value of the last character transmitted by serial port 0. Note that you cannot assign values to the SxOUT VTREGs. You may use the SxOUT VTREG in a script to process transmitted data. For example,

signal void s0out_sig (void) {
while (1)
  {
  wwatch(S0OUT);     /* wait for something in S0OUT */
  printf ("Transmitted a %2.2X\n", (unsigned) S0OUT);
  }
}

SxTIME VTREG
Data Type: unsigned char

The SxTIME VTREG allows you to control the timing of the simulated serial port 0, 1, and so on.

• A value of 1 (which is the default) indicates that the serial port timing is identical to the target hardware. Use this value when you want to see the effects of baud rate on the serial port I/O.
• A value of 0 indicates that all serial input and output occur instantaneously. Use this value when you don't care about any baud rate effects or when you want serial output to be fast.

For example:

S0TIME = 0   /* Set Serial Port 0 for FAST timing */
S0TIME = 1   /* Set Serial Port 0 for accurate timing */