Peripheral Simulation

For Silicon Laboratories, Inc. C8051F362 — A/D Converter (21x10-bit)

Simulation support for this peripheral or feature is comprised of:

• Dialog boxes which display and allow you to change peripheral configuration.
• VTREGs (Virtual Target Registers) which support I/O with the peripheral.

These simulation capabilities are described below.

Analog/Digital Converter 0 Dialog

The Analog/Digital Converter (ADC) dialog displays and configures the A/D converter. The controls in this dialog are separated into several logical groups.

Analog Digital Converter

• ADC0CN contains the following ADC control register settings:
• ADC0EN (ADC0 Enable) is set to enable the A/D converter.
• ADC0TM (ADC Track Mode) is set to enable low-power track and hold mode.
• ADC0INT (ADC Interrupt) is set when an A/D conversion completes.
• ADC0BUSY (ADC Busy) is set when and A/D conversion is in progress.
• ADC0WINT (ADC Window Compare Interrupt) is set when a Window Comparison Match occurs.
• ADC0LJST (Left Justify Select) is set to left-justify the ADC0H and ADC0L register. If reset, they are right-justified.
• AMX0SL (Channel Select Register) is used to select the ADC input.
• ADC0CF contains the SAR Clock and PGA ADC control register settings.
• ADC0CM (ADC Conversion Mode) selects the event that starts the A/D conversion.
• ADC0H (ADC High-Order Data Word) contains the MSB of the 10-bit ADC result. ADLJST affects where data is located in this byte.
• SAR Clock 0 displays the calculated SAR (Successive Approximation Register) clock value derived from the system clock and bits 7-3 in ADC0CF.

Programmable Window Detector This feature continuously compares the output of the ADC to the following limit registers and notifies the system when an ADC output falls outside of this range:

• ADC0GT (Greater Than Data High Byte Register) is the high limit reference value.
• ADC0LT (Less Than Data High Byte Register) is the low limit reference value.

Reference Voltages

• VREF contains the bandgap output reference voltage.
• VDD contains the power supply voltage.
• REF0CN (Reference Control Register) contains the following controls:
• IOSCEN (Internal Oscillator Enable) is set to enable the chip's internal oscillator.
• REFSL (Reference Source Select) is set to use the VDD pin as a reference source. If reset, the source is external.
• TEMPE (Temperature Sensor Enable) is set to enable the internal temperature sensor.
• BIASE (Bias Generator Enable) is set to enable internal bias voltage generation.

Analog Input Channels

• AINx (Analog Input Channels x) displays the analog voltage value input for each channel.

Temp. Sensor

• TEMP (Temperature) displays the on-chip (die) temperature.
• VTEMP (Temperature Output Voltage) is the the voltage input to the PGA when the Temperature Sensor is selected.

AINx VTREG
Data Type: float

The AINx VTREGs set the analog input voltages for simulated A/D converters. The AINx VTREGs represent the inputs to the analog input pins of the MCU for analog input 0, 1, 2, and so on. AIN0 sets the input voltage for analog input #0, AIN1 sets the input voltage for analog input #1, etc. If you have properly configured the analog inputs, the following commands (typed in the debugger's Command Window) input the voltages specified.

AIN0 = 0.000  /* Analog Input 0 = 0.000 volts */
AIN1 = 2.500  /* Analog Input 1 = 2.500 volts */
AIN2 = 4.999  /* Analog Input 2 = 4.999 volts */

You may create a debugger signal function to periodically change the value of the A/D input. The following signal function increases the A/D Channel 1 input voltage by 0.1 volts each second.

signal void AIN1_sig (void) {
float f;

for (f = 0.0; f < 5.0; f += 0.1)
  {
  swatch (1.0);                  // Delay 1 second
  AIN1 = f;                      // Set AIN1 Voltage
  }
}

SARCLK0 VTREG
Data Type: unsigned long

The Successive Approximation Register (SAR) clock used for A/D conversion. It is based on the system clock (CLOCK VTREG) and can be adjusted by the setting in bits 7-3 of ADC0CF.

TEMP VTREG
Data Type: float

TEMP contains the on-chip temperature sensor in degrees (centigrade). The on-chip temp sensor measures temperature of the chip die. TEMP is used as the VTEMP output voltage to the PGA. The following command (typed in the debugger's Command Window) sets the die temperature.

TEMP = 30.5

VDD VTREG
Data Type: float

VDD is the digital supply voltage.

VREF VTREG
Data Type: float

VREF contains the bandgap output reference voltage.

VTEMP VTREG
Data Type: float

VTEMP is the the voltage input to the PGA when the Temperature Sensor is selected.